Cart  

No products

0,00 € Shipping
0,00 € Total

Prices are tax excluded

Cart Check out

24 Vdc output

New products

  • RI-D18-100-CT

    RI-D18-100-CT

    single phase  energy meter - 100 A

    100,00 €

  • RI-D175-P

    RI-D175-P

    single phase MID energy meter - 45 A

    43,08 €

  • Connect X LT

    Connect X LT

    The Connect X, our all-rounder,...

    1 106,31 €

  • Connect XM LT

    Connect XM LT

    The Connect XM finds its application...

    967,85 €

  • Connect XF LT

    Connect XF LT

    The Connect XF is designed to enable...

    1 037,08 €

  • Connect XH LT

    Connect XH LT

    The Connect XH serves as our complete...

    857,08 €

All new products

UPSOTEC 2440

DC-UPS for batteries, primary : 24 V, secondary : 24 V, output: 40 A, dimensions: 123x85x143 mm, weight: 0.9 kg

More details...

Availability : 1-2 weeks

UPSOTEC 2440

485,75 €

DC-UPS for batteries, primary : 24 V, secondary : 24 V, output: 40 A, dimensions: 123x85x143 mm, weight: 0.9 kg

 

Technical Data

Input  
Nominal input voltage 24 V DC (22...30 V DC) SELV
Min. nominal input voltage for charching operation 22,5 V DC +/-2%
Output  
Nominal output voltage mains operation 27,7...19,2 V DC
Nominal output voltage back-up operation with temperature tracking 24 V DC (22...30 V DC)
Max. nominal output voltage 40 A
In General  
Protective system IP20
Operational temperature -25°C...50°C
Dimensions 123 x 85 x 143 mm
Weight approximately 0,9 kg

The DC UPS series UPSOTEC is capable to provide an uninterruptible power supply as well with batteries as with ultracapacitors. All CEM modules (24 V DC) as well as the battery modules up to 40 Ah can be used in combination with the UPSOTEC series.

The UPSOTEC is the right way to back up a power failure without failures and downtimes in production.
An externally connected battery allows backup times up to the hours. However, if only a short back up time and a maintenance-free energy storage is needed, which is also suitable for high temperatures, the choice falls on an ultracapacitor module. 

The DC-UPS UPSOTEC includes a charging and monitoring system inside the housing, which charges the externally connected energie store. The UPS is supplied by an external regulated DC power supply. In case of an interruption of the DC supply, the energy of the energie store is released unregulated. The load is supplied from the UPS until the voltage drops below the deep discharge limitation. The back-up time depends on the state of charge of the energie store and on the discharge current.

The power supply has the following characteristics:
  • Mikrocontroller based charging and discharging
  • Charging of battery and ultra capacitor possible
  • Monitoring of the mains with potentialfree contacts, LED and USB
  • Display of state of Charge with Signal light
  • Vibration secured wiring with spring-type technique
  • High efficiency
  • Wide temperature range -25 °C up to 50 °C
  • Shutdown input for early stop of the buffering
  • Monitoring of the battery (internal resistance, fuse, presence)
  • Reverse polarity protection
  • USB Interface for monitoring, IC mode an parameterization
  • Monitoring of the energy store operating hours
  • primary voltage 24 V
  • secondary voltage 24 V

2 other products in the same category :

UPSOTEC 2403

UPSOTEC 2403

327,60 €

UPSOTEC 2420

UPSOTEC 2420

385,27 €